
What Is DPF Regeneration?
DPF, an acronym for ‘Diesel Particulate Filter’, is a filter that has been created to catch and store the soot from your vehicle’s exhaust. It’s basically a ‘soot trap’ which has been put on the car to avoid that soot from entering into the atmosphere. It’s an emission reducer to help create a better environment.
With every filter there is a limit as to how much soot can be trapped inside of it. As a result, the filter needs to go through a process where that soot is ‘burned off.’ This burning off of particulates is known as the regeneration process.
The aim of the regeneration process is to burn off all of the trapped particles so that when the residue comes out it is less harmful to the environment.
All vehicles from 2009 began to fit a DPF to their diesel vehicles. It was their way of playing their part to having a better impact on the emissions that come from the toxic burning of particulates coming from their exhausts. It’s a way for manufacturers to comply with stringent emission regulations as well as provide a way to produce cleaner diesel vehicles.
The regeneration process converts all the soot to ash through the use of heat, chemical reaction and electricity. The combustion temperatures can get very high and typically range from 250˚C – 350˚C range (with a chemical or fuel catalyst) to the 550˚C range (without a catalyst).
The main catalyst used to create the correct environment to allow soot to regenerate within the DPF are referred to as DOCs (Diesel Oxidation Catalysts).
When it comes to burning off these toxic particulates, there are 2 main ways to do this. These process are called ‘regeneration’ and the two main types are:
• Passive regeneration and;
• Active regeneration
PASSIVE REGENERATION:
For the motorway driver who drives long distances
This is when a driver is driving the vehicle without the sole purpose of trying to ‘regenerate.’ It’s a process where the vehicle will try to regenerate through the everyday driving for long periods of time (e.g. motorway driving).
Passive regeneration occurs when the car is running at speeds typically over 80k/h on long motorway journeys which allows the exhaust temperatures to increase significantly and cleanly burn off the excess soot in the filter.
It’s common that a large percentage of drivers aren’t driving their vehicle regularly or for extended periods of time which manufacturers have then designed another form of regeneration to cater for this. This process is known as ‘active generation.’
ACTIVE REGENERATION:
For the driver who doesn’t drive long distances
Since many drivers do not use their cars to drive long distances on the motorway on a regular basis, manufacturers had to come up with a different way to clear the DPF of particles. They came up with a system in which active regeneration is activated when the amount of soot gathered in the DPF reaches a certain level. It’s an automatic process which injects more fuel (as part of the ECU in the vehicle telling it to do so). It is common that this process starts with the DPF’s level of soot is sitting around the 45% level.
When the soot gathered reaches the 45% level, the temperature of the exhaust will increase as a result of post combustion fuel injection. Even if the vehicle is not travelling at a high speed, the exhaust becomes hot enough to burn off all of the soot which has collected in the DPF.
If the active regeneration process is in progress and you find yourself reaching your destination before it has had a chance to burn the particulates properly, you can find that your vehicle’s DPF light may come on.
What if your DPF light comes on?
If you see your DPF light glowing, it’s a quick indicator that your DPF is starting block and needs to be ‘unblocked’. A sure sign that the regeneration phase needs to be activated. One of the easiest way to start the regeneration process is to take your vehicle for a long drive at speeds of 80 to 100km/h for 30mins to 1 hour. The key is to find open roads (i.e. motorways) to keep the vehicle from stop starting and to keep the temperatures of the exhaust consistent at a high rate.
You will notice the DPF light will disappear when it has finished the regeneration process and the filter is cleaned out.
In some diesel vehicles, you can manually start the regeneration while driving or in a stationary/parked position. In order for you to do so you can turn on a car switch or engage your car brake to start the process. For those with car scan tools you can also perform an active regeneration through this process.
Newer vehicles today perform automatic active DPF regeneration when the filter reaches a certain capacity of around 45%. The automatic DPF regeneration also happens for a specific number of kms driven. The process can typically last for around 10-15 minutes.
What if the DPF is blocked and the light doesn’t go off?
DPF’s are not a cheap part to replace or repair. You should treat this seriously if this happens and you should always seek the guidance of a professional who knows about DPFs and your vehicle.
There are a range of options to fix blocked DPFs and one common option which will save you a significant amount of money (as opposed to replacing the entire DPF) is what is known as ‘DPF cleaning’.
DPF cleaning is an affordable option to clean out all of the backed up soot so that it can start to work better both for on road performance and for the environment.
Auto Stop are professionals in DPF cleaning and we have a comprehensive service for DPF cleaning in both Brisbane and Gold Coast. Contact us for any DPF issues you may have, we’re here to help.